Get An Estimate

 

 

The publisher is making several good points on the subject of Installing A Bathtub as a whole in this great article following next.

Setting up a bath tub isn't specifically rocket science, but it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is also a reasonably hard task. If the old tub is easily obtainable, the task can relocate speedily; if you have to open up a wall surface to remove the old tub as well as place the new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as embeded in the new one. Ensure you have qualified on your own for the work and also are comfortable attempting it. Instead of employing a service provider to take over a halfway-completed project, it is better to consider employing one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This write-up will certainly help you install a new bathtub in your restroom if you have currently gotten a new tub as well as do not require to alter the setup of your previous water pipelines.
Your devices and also product list need to consist of the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Planning for the Installment

To start with, the sustaining frame supplied with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its final placement.

 

 

Removing Old Touches

If you require to replace old taps with new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, turn on the taps to drain pipes any type of water staying in the system. The process of removing the existing faucets can be rather troublesome due to the limited gain access to that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipes. When the supply pipelines have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

 

 

Installing the Tub

Making use of the two wood boards under its feet, place the tub in the required setting. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the level and also adjusting the feet on the tub till the spirit level checks out degree.
To install faucets, fit all-time low of the furthest versatile faucet connector to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the water system and also check all joints as well as brand-new pipework for leakages and tighten them if required. Load the bathtub and likewise examine the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has actually been made use of at the very least once as this will settle it into its last placement.

 

 

Suitable New Touches

If the tails of the new taps are plastic, then you will require a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the tap and the other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly need lowering couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washers are in location in between the faucet and also the sink. Secure the tap in place with the supplier provided backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type ought to be linked to the tap ends first, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

 

 

Tiling Around the Bath tub

In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, causing issues with moisture as well as possible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill the bathtub with water prior to securing, to enable the motion experienced when the tub is in usage. The sealer can break fairly early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly available on the marketplace. It is recommended to fit the tiles utilizing water-resistant or water-proof sticky and cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I hope you enjoyed our part about How to Install a Bathtub Yourself. Thanks a lot for finding the time to browse our short article. Liked our blog? Please share it. Help another person find it. Thank you for your time. Don't hesitate to check up our website back soon.

Website